.net 2.0 problems
 

I developed my addin in Visual Studio 2003 using .net 1.1, now when I
try to run my addin on a machine that has .net 2.0 it does not load and
in fact the load behavior changes from 3 to 2 even though it works fine
on a machine with .net 1.1 installed.
Any ideas?
Thanks

.net 2.0 problems
 

Hello,


1. Are there other add-ins developed on .net framework 2.0 installed on this
machine?
2. Have you cheked your add-in in the disabled items?
3. Have you installed the hotfix for framework 2.0 that allows to run shared
add-in?
4. Do you have any msm modules in your setup project?


Regards from Belarus,
Eugene E. Starostin
---

A .NET steroid for developing add-ins and smart tags for Microsoft Office -
http://www.add-in-express.com



"Rog" wrote in message
...
I developed my addin in Visual Studio 2003 using .net 1.1, now when I try
to run my addin on a machine that has .net 2.0 it does not load and in fact
the load behavior changes from 3 to 2 even though it works fine on a
machine with .net 1.1 installed.
Any ideas?
Thanks

.net 2.0 problems
 

have not installed the .net 2.0 framework hotfix.
Can you point me to the url for this?
Thank you very much for your help.

Eugene E. Starostin wrote:
Hello,


1. Are there other add-ins developed on .net framework 2.0 installed on
this machine?
2. Have you cheked your add-in in the disabled items?
3. Have you installed the hotfix for framework 2.0 that allows to run
shared add-in?
4. Do you have any msm modules in your setup project?


Regards from Belarus,
Eugene E. Starostin
---

A .NET steroid for developing add-ins and smart tags for Microsoft
Office - http://www.add-in-express.com



"Rog" wrote in message
...
I developed my addin in Visual Studio 2003 using .net 1.1, now when I
try to run my addin on a machine that has .net 2.0 it does not load
and in fact the load behavior changes from 3 to 2 even though it works
fine on a machine with .net 1.1 installed.
Any ideas?
Thanks

.net 2.0 problems
 

Rog,

You need to install the following updates for MS Office and Visual Studio
..NET 2005 (if you have installed on this machine).
http://www.microsoft.com/downloads/d...displaylang=en

http://support.microsoft.com/kb/908002



--
Regards from Belarus,
Eugene E. Starostin
---
http://www.add-in-express.com
A .NET steroid for developing add-ins and smart tags for Microsoft Office



"Rog" wrote in message
...
have not installed the .net 2.0 framework hotfix.
Can you point me to the url for this?
Thank you very much for your help.

Eugene E. Starostin wrote:
Hello,


1. Are there other add-ins developed on .net framework 2.0 installed on
this machine?
2. Have you cheked your add-in in the disabled items?
3. Have you installed the hotfix for framework 2.0 that allows to run
shared add-in?
4. Do you have any msm modules in your setup project?


Regards from Belarus,
Eugene E. Starostin
---

A .NET steroid for developing add-ins and smart tags for Microsoft
Office - http://www.add-in-express.com



"Rog" wrote in message
...
I developed my addin in Visual Studio 2003 using .net 1.1, now when I
try to run my addin on a machine that has .net 2.0 it does not load and
in fact the load behavior changes from 3 to 2 even though it works fine
on a machine with .net 1.1 installed.
Any ideas?
Thanks

.net 2.0 problems
 

So I tool my project from VS 2003 and opened it in VS 2005. Installed
these updates, but it does not seem to help. As a side note, I am using
a Shim in order to load my add-in. Is this a problem.
Each time I start Outlook the Loadbehavior gets reset from 3 to 2.
Any ideas?
Rog

Eugene E. Starostin wrote:
Rog,

You need to install the following updates for MS Office and Visual
Studio .NET 2005 (if you have installed on this machine).
http://www.microsoft.com/downloads/d...displaylang=en


http://support.microsoft.com/kb/908002

.net 2.0 problems
 

That is a good question, but yes it was installed on this machine.
If you want to make your add-in totally compatible with .NET 2.0 can
you still use a SHIM what more do you need to do ?
Rog

sublimese wrote:
This might be a stupid question, but is the .NET framework 1.1
installed on the machine you are trying to get this to work on?
(It seems like most of time when I am trying to figure out why
something isn't working for me, its something totally obvious and
simple, and thus I always overlook it until I have spent hours and
hours trying to figure it out).

.net 2.0 problems
 

I solved this problem. I have posted my steps he
http://blog.alkirasoftware.com/?p=14

Thanks,
Rog

wrote:
That is a good question, but yes it was installed on this machine.
If you want to make your add-in totally compatible with .NET 2.0 can
you still use a SHIM what more do you need to do ?
Rog

sublimese wrote:
This might be a stupid question, but is the .NET framework 1.1
installed on the machine you are trying to get this to work on?
(It seems like most of time when I am trying to figure out why
something isn't working for me, its something totally obvious and
simple, and thus I always overlook it until I have spent hours and
hours trying to figure it out).